OKBaby Flipper Evolution Bath Seat Grey

-OKBaby Flipper Evolution -bath seat -gray -suction cup attachment -thermometer and water level indicator -seat with a non-slip surface -ex-display condition, very good; packaging may be damaged or replaced OKBaby Flipper Evolution is a gray bath seat for use in a bathtub. Its contoured seat has a rubber surface, and suction cups attach the base to a suitable bathtub bottom. The built-in thermometer and water level indicator help you prepare the bath. There are play features at the front to keep your child interested during bath time. This model is designed for children who can sit up independently, from around six to fifteen months old, weighing up to thirteen kilograms. Stop using it when your child starts trying to stand up independently. The bathtub bottom must be smooth, clean and undamaged; the seat is not suitable for non-slip surfaces. The caregiver must remain in contact with the child throughout the bath. Care and safety Rinse and dry the seat thoroughly after bathing. Do not use solvents or abrasive cleaners. Before first use, read the manufacturer's markings and make sure all parts are correctly secured and used as intended. Regularly check the condition of children's accessories and keep them clean in accordance with the manufacturer's recommendations. If the product is used with other equipment, check that the dimensions, installation method and required accessories are compatible before use. HOW TO INSTALL AND USE THE “FLIPPER EVOLUTION” BATH SEAT CORRECTLY OKBABY REF. 799 Read these instructions carefully before use and keep them for future reference. • The caregiver must remain in contact with the child at all times. • Drowning can occur very quickly, even in very shallow water (± 2 cm). • This product does not provide additional protection against water-related hazards, and drownings have occurred while using bath seats. AGE OF USE: from 6 to approximately 15 months. - MAX. 13 kg. HOW TO USE: 1. Make sure the bathtub surface is clean, smooth and undamaged, and is not a non-slip surface (embossed patterns, satin-finish areas, etc.). 2. Place the seat on the bottom of the bathtub, making sure the child cannot reach the taps (Figure 1). 3. Press the seat firmly against the bottom (Figure 2) to attach the suction cups. Check that all four suction cups are attached to the bathtub bottom by trying to lift the seat gently. 4. Before placing the child in the seat, have all the items needed for the bath within reach. This is necessary so that you never leave the child alone. 5. Fill the bathtub with warm water (recommended temperature: 37°C or 99°F) up to the level marked on the outer side of the seat (Figure 3). 6. Place the child in the seat as shown in Figure 3. Always check the water temperature before putting the child in. 7. After the bath, take the child out of the seat before removing the seat from the bathtub. 8. Remove the seat by lifting the outer edge of each suction cup (Figure 4). Do not pull forcefully. 9. Rinse the seat thoroughly and dry it before putting it away. Do not use any solvents or abrasive products. To help the suction cups last longer, store the seat with the suction cups unloaded or resting on a completely flat surface. IMPORTANT NOTES: • Do not use this bath seat until the child can sit up independently (around 6 months). • Do not use this bath seat once the child can stand up independently (around 15 months). • Do not use this bath seat on non-slip or damaged surfaces. • This bath seat is not suitable for multi-level bathtubs. • Before use, check that the bath seat is firmly attached to the bathtub with all suction cups by trying to pull it off. • Stop using the bath seat if the suction cups lose their grip or are damaged. • Make sure the water level does not exceed the mark on the bath seat. • It is dangerous to leave a child in the care of a minor. • Check that the water is not too hot (it must not exceed 37°C or 99°F). Manufacturer's warnings — verified Polish translation The product may only be used once the child can sit up independently, and until the child starts trying to stand up independently. *Do not use the product in a bathtub with an uneven bottom. WARNING! To remove the product, lift the edges of the suction cups. Manufacturer's warnings — verified Polish translation RECOMMENDED BATH TIME: 10 min FAQ What age child is the seat suitable for? It is suitable for a child who can sit up independently, is around six to fifteen months old and weighs up to thirteen kilograms. Stop using it when the child starts trying to stand up independently. Does it fit every bathtub bottom? No. The bottom must be smooth, clean and undamaged. Do not use the seat on a non-slip bottom or in a multi-level bathtub. Does the model have a thermometer? Yes, it has a built-in thermometer and a recommended water level indicator. Specifications Shipping time: 24 hours Safety documents OKBaby Flipper Evolution manufacturer information: https://files.manclouds.com/html/nl/okbaby/flipper-evolution/html/flipper-evolution8.page OKBaby Flipper Evolution manufacturer information: https://www.okbaby.it/documenti/799_FLIPPER_EVOLUTION.pdf OKBaby Flipper Evolution manufacturer information: https://files.manclouds.com/html/nl/okbaby/flipper-evolution/html/flipper-evolution3.page